How To Change Code On Genie Excelerator Garage Door Opener: A Step-by-Step Guide

Garage door openers have become an essential part of home security, and the Genie Excelerator Garage Door Opener is one of the most trusted models on the market. However, to maintain security and prevent unauthorized access, it’s crucial to update your access code periodically.

In this guide, we’ll walk you through how to change the code on a Genie Excelerator garage door opener quickly and efficiently. Whether you’re updating your remote control settings, reprogramming the keypad, or resetting the system, this article covers everything you need to know.

Why You Should Change Your Genie Excelerator Garage Door Opener Code

Before we dive into the steps, let’s discuss why updating your garage door opener code is essential:

1. Enhanced Security – Changing the access code reduces the risk of unauthorized entry.
2. Prevent Signal Interference – Older codes can be picked up by other remotes, leading to accidental openings.
3. Lost or Stolen Remote – If your remote has been misplaced, resetting the code prevents misuse.
4. New Homeowners or Tenants – If you’ve recently moved into a new home, changing the garage code ensures that no one else has access.

How To Change Code On Genie Excelerator Garage Door Opener

Updating the code on your Genie Excelerator Garage Door Opener involves different methods depending on whether you’re changing the keypad PIN, remote control, or completely resetting the system. Below are detailed instructions for each scenario.

1. Changing the Code on the Genie Wireless Keypad

The Genie Wireless Keypad allows you to open the garage door using a PIN. Follow these steps to change the access code:

1: Clear the Existing Code

1. Locate the “Learn” button on the Genie Excelerator motor unit (usually near the antenna).
2. Press and hold the Learn button until the indicator light turns off. This erases all existing keypad codes.

2: Program a New PIN

1. Press and hold the Program button on the keypad until the LED light blinks.
2. Enter your new PIN (3 to 8 digits) and press the Up/Down arrow button.
3. The LED will flash, indicating the new code has been set.
4. Test the new code by entering it on the keypad and pressing the Up/Down arrow. The garage door should respond.

2. Changing the Code on a Genie Remote Control

If you want to update the Genie Excelerator remote control, follow these simple steps:

1: Clear Previous Programming

1. Locate the “Learn” button on the garage door opener.
2. Press and hold it until the indicator light goes out, erasing all stored remote codes.

2: Reprogram the Remote

1. Press the Learn button again until the LED light starts flashing.
2. Within 30 seconds, press the button on your Genie remote that you want to program.
3. The opener’s LED light will blink, indicating that the remote has been successfully paired.
4. Test the remote by pressing the programmed button to ensure the garage door opens and closes.

3. Resetting the Entire Genie Excelerator System

If you need to completely reset your Genie Excelerator garage door opener, follow these steps:

1: Disconnect Power

1. Unplug the garage door opener from the power outlet.
2. Wait 5 minutes to allow the system to reset.

2: Erase All Codes

1. Plug the opener back in and locate the Learn button.
2. Press and hold the Learn button for 10 seconds until the light turns off.
3. This will erase all programmed remotes, keypads, and wall consoles.

3: Reprogram the Devices

1. Follow the remote and keypad programming steps mentioned above to set up new access codes.

Common Issues When Changing the Code & Troubleshooting Tips

Even with detailed instructions, you might encounter some issues when changing the code on your Genie Excelerator garage door opener. Here are a few common problems and solutions:

1. Remote Control Not Working After Reprogramming

• Ensure the battery is fresh in the remote.
• Move closer to the garage door opener when programming.
• Clear all previous codes and start over.

2. Keypad Not Responding

• Check if the keypad batteries are working.
• Make sure you’re entering the correct PIN.
• Reset the system and reprogram the keypad.

3. Garage Door Opener Light Blinks But Doesn’t Open

• This could indicate interference or a weak signal.
• Check for any obstructions blocking the garage door sensors.
• Try reprogramming the remote and keypad.

Tips for Maintaining Your Genie Excelerator Garage Door Opener

To keep your Genie Excelerator Garage Door Opener functioning optimally, follow these maintenance tips:

1. Regularly Change the Access Code – Update the keypad and remote codes at least once a year.
2. Inspect the Sensors – Ensure the garage door safety sensors are aligned properly.
3. Lubricate Moving Parts – Apply garage door lubricant to reduce wear and tear.
4. Check for Signal Interference – Keep electronic devices away from the opener to prevent frequency disruption.

Final Thoughts

Knowing how to change the code on a Genie Excelerator garage door opener is crucial for maintaining home security. Whether you’re updating the keypad PIN, reprogramming the remote control, or performing a full system reset, these steps will ensure that your garage remains secure from unauthorized access.

By following this guide, you can effortlessly change your access code and enhance the security of your garage door system. If you experience any difficulties, refer to the troubleshooting section or consult Genie’s official support for further assistance.